Skip to main content

LiCheng Teach You Operate And Maintain Flat Screen Printer

We should focus on the preparation for starting up, operation and closing down. If you follow that, the service life of the Flat Screen Printing Machine will be extended and work efficiency will be improved. Some operations are as follow.
First, prepare the printing process according to the process and sample requirements.
Second, determine the number of cloth and connect the belt according to the product situation.
Third, adjust the amplitude of the glue and the thickness of the glue.
Fourth, adjust the water washing device.
Fifth, carry out registration.
Sixth, according to the process requirements, grind the blade edge and match the color paste bucket as needed.
Seventh, connect the white cloth and the end of the cloth guide band, push the glue-on mechanism, and drive according to the electrical program so that hot air will be circulatory, and drying room will be heated.
Eighth, after one cycle, the front of the flower cloth is connected with the guide cloth belt in the drying room, the drying room linkage clutch is operated, and the flower cloth enters the drying room.
On the other hand, prompt maintenance also plays an important role in extending the service life of the Flat Screen Printer . It’s advisable to take the following measures.
First, when the phototube is damaged, the registration is wrong, the light control is out of order, and the photodiode and phototube should be adjusted.
Second, when the lift switch is out of order, and the machine stops, you should check whether travel switch is fine or not.
Third, when the scraper action fails, check the travel switch. When the times of squeegee is incorrect, the counting device is faulty.
Fourth, the whole machine electrical components need to be inspected whether the inspection work is normal once a week. In addition, check whether the screw is loose and the contact is good.
Fifth, if the temperature of the drying room can’t reach a standard level, the cloth is not dry, you can use the "up delay" or "down delay" to make appropriate operation, or start the exhaust to exclude water vapor.
Sixth, in the event of an accident, press the “Emergency Stop” button and the machine will stop running immediately. If the fault cannot be cleaned within 5 minutes, stop heating to remove steam. More flat screen printing machine information :https://www.hotairstenter.com/product/flat-screen-printing-machine.html

Comments

Popular posts from this blog

Preliminary Preparation of Rotary Screen Printing Machine II

Requirements for the glue of Open Type Rotary Screen Printing Machine Since 80% of the defects in the printing process are caused by the printing paste, there are strict requirements on the quality of the glue, mainly including: The glue must be prepared before opening the machine . The color of the glue must match the original. The glue should maintain a proper consistency. Generally, the thinner the fabric, the greater the consistency of the glue, the finer the pattern, and the consistency of the glue. The printing paste should be fully dissolved. After the preparation is completed, the nylon mesh should be used for filtration to avoid impurities blocking the net or damage the rotary screen. Requirements for rotary screen printing machine The rotary screen printing machine should be thoroughly inspected before driving to ensure that there are no foreign objects in the printed tape to avoid damage to the tape. The temperature of the drying room should be adjust...

Inaccurate Registration of Rotary Screen Printer

When two or more patterns of registrations are printed, all or part of the patterns on the printed fabric are staggered or overlapped, which is seriously inconsistent with the original, called inaccurate registration. (1)Constant Inaccurate Registration Constant Inaccurate Registration means that the registration is not inaccurate from the start of driving, and the corresponding pattern always shifts from the original position or overlaps. The low impact factors of such problems can be found in the following reasons: the accuracy of the printing machine, the rotary screen and its plate making, the process, the operation, the printed fabric, and the patch pulp. (2)Inaccurate Left and right Registration That is to say, the registration is accurate in the middle, but inaccurate on the right or left. In this case, it is necessary to check whether the mechanical operation of the rotary screen printing part is normal; whether the film draft conforms to each set of film ...

ZCMD768 Type Hot Air Stenter

The Hot Air Stenter Machine is always used for stretching and tensioning the fabric by heating and stretching the two sides with uniform width. The continuous flat dyeing and finishing of knitted fabrics can optimize printing quality, and reduce damage to the fabric with excellent flexibility. In addition, it can reduce the cost of the mercerizing machine. The hot air stenter is mainly used to make the weaving machine. Generally, the hot air stenter uses the heat transfer oil to heat the air in the setting machine, and then heats the fabric. When the fabric reaches a certain temperature and remains for a certain period of time, the structure of the fabric changes to achieve the purpose of setting. The double-point lining coater is the main equipment for processing high-grade low-elastic linings and thin non-woven linings. It mainly consists of several parts such as retort, slurry coating, dust coating, up and down suction, drying room, cooling and winding, pneumatic a...