Skip to main content

Maintenance of Open Rotary Screen Printing Machine

In order to use Open Type Rotary Screen Printing Machine smoothly, you should pay attention to the following points:
 
First, before you open it, check whether there is any residual glue on rotary gluing part. If any, remove it with a trowel. Otherwise, the guide tape will be indented. If you use a short net on the wide-format printing machine, you should pay more attention to. Because the indentation printed on the center of the tape directly affects the printing effect of the wide fabric. In addition, cover the net and the bulkhead with tape to prevent the tape from damage.

Second, check whether the air pressure of the compressed air is normal, otherwise, the net is damaged due to insufficient tension of the net when the machine is turned on.

Third, check whether the blade is clamped or firm and there are sharp edges at both ends of the blade to avoid the scraper on both sides and the middle of the pressure is inconsistent or cut the round net. If it is a magnetic rod printing, check whether the magnetic rod is bend, or it will be easy to appear horizontal stripes.

Fourth, check if the rotary net seat is flexible, or it will be twisted easily.
Fifth, check whether the heating temperature of the arc scraper should not exceed 160℃, otherwise it is easy to burn the cloth and the guide tape.

Sixth, the pump can’t be idling for 30s, otherwise the blade will be damaged. When beating, you should first water 0.5min to make the leaves permeable for normal use.
Seventh, when the guide belt is clean, never wash it to prevent water from entering into the cylinder or electrical components.

Eighth, when the water washing device is waterless, it is not allowed to drive to avoid scratching the guide tape.
Open type rotary screen printing machine and Flat Screen Printing Machine from hotairstenter.com are superior in quality and competitive in price. https://www.hotairstenter.com/product/ welcome your visit.
Labels:

Comments

Post a Comment

Popular posts from this blog

Structural Characteristics of Hot Air Stenter Machine

The Hot Air Stenter machine is mainly composed of the feeding part, the weft feeder, the chain, the oven body, and the falling cloth. Apart from that, chemical systems and oil furnace heating systems. 1.Feeding part The structure is relatively simple, consisting of a trough and a roll. The cloth enters the trough, carries the chemical material, and then presses the excess chemical material through the roll to clean it. Therefore, the chemical material on the cloth is very uniform, which is a prerequisite for obtaining a high quality styling cloth. It is necessary to always pay attention to whether the pressure on the left and right sides of the roll is consistent. Otherwise, the side with less pressure is loaded more, while the one with higher pressure is less loaded, and the cloth will have quality problems such as inconsistency. 2. Weft feeder The weft aligner on the fixed machine has four sets of sensors. Each sensor consists of two parts: illuminating and sen
Post a Comment
Read more

LiCheng Flat Screen Printing Machine

Zhejiang LiCheng is devoted towards offering the qualitative range of Flat Screen Printing Machine , as per client’s precise need and requirements.   Flat screen printing machine working principle: Take the commonly used hand-screen flat screen printing machine as an example, the working principle of the screen printing machine can be described as follows: The transmission mechanism transmits the power so that the squeegee squeezes the ink and the screen printing plate during the movement so that the screen Printing plate and the substrate to form a nip, the screen has tension N1 and N2, the force on the squeegee F2, rebound so that the screen printing plate in addition to the imprinting line are not in contact with the substrate, the ink in Under the action of the squeezing force F1 of the squeegee, the squeegee slides from the moving nip to the substrate through the mesh. In Flat Screen Printing Technology the screen is flat and moves up and down. the Squeeze is
Post a Comment
Read more

Feeding Operation of Hot Air Stenter

Do you are already familiar with the feeding operation of the Hot Air Stenter machine? Although this operation is relatively simple, the problems that need attention are relatively trivial, and this operation will affect the subsequent processing effect of the hot air stenter machine. So as a user, we also need to pay attention to this part of the content. In actual work, we must wear the guide cloth according to the requirements, and check the worn guide cloth to ensure correctness. Then we need to clean the hot air stenter machine first, especially pay attention to check the cloth rack and the front of the machine for dirt, and clean it in time. In addition, you need to check the needle clip for debris and clean it up. In addition, the site environment should be kept clean and hygienic. When the inspection work is completed, we need to classify the fabrics to be produced according to the process conditions. Generally, the same process fabrics will be used for centr
Post a Comment
Read more