Skip to main content

Preliminary Preparation of Rotary Screen Printing Machine II

Requirements for the glue of Open Type Rotary Screen Printing Machine
Since 80% of the defects in the printing process are caused by the printing paste, there are strict requirements on the quality of the glue, mainly including:
The glue must be prepared before opening the machine .
The color of the glue must match the original. The glue should maintain a proper consistency. Generally, the thinner the fabric, the greater the consistency of the glue, the finer the pattern, and the consistency of the glue. The printing paste should be fully dissolved. After the preparation is completed, the nylon mesh should be used for filtration to avoid impurities blocking the net or damage the rotary screen.
Requirements for rotary screen printing machine
The rotary screen printing machine should be thoroughly inspected before driving to ensure that there are no foreign objects in the printed tape to avoid damage to the tape.
The temperature of the drying room should be adjusted according to different glues. If the temperature is too high, the fabric will feel hard, damage the surface film, affect the color fastness, and the temperature will be too low. The surface glue of the fabric is not completely dried, which will cause stickiness and seriously affect the product quality.
All the printing machine bodies should be fully inspected, and the faults should be repaired in time to prevent the parking of the machine parts during the printing process.
The printing machine personnel should be fully equipped, specifically one for each of the front and the rear, one for the pulp, one for the cloth.
The patch adhesive on the printed tape should have sufficient viscosity to make the fabric and the tape tightly attached to ensure the fabric is flat.
As a manufacturer of rotary screen printing machine, Flat Screen Printing Machine and Hot Air Stenter , we are committed to solving the complete product design and sample verification supporting solutions for major customers, providing customers with high quality products and superior service. If you interested in our products, please feel free to contact us any time.
Labels:

Comments

Post a Comment

Popular posts from this blog

Feeding Operation of Hot Air Stenter

Do you are already familiar with the feeding operation of the Hot Air Stenter machine? Although this operation is relatively simple, the problems that need attention are relatively trivial, and this operation will affect the subsequent processing effect of the hot air stenter machine. So as a user, we also need to pay attention to this part of the content. In actual work, we must wear the guide cloth according to the requirements, and check the worn guide cloth to ensure correctness. Then we need to clean the hot air stenter machine first, especially pay attention to check the cloth rack and the front of the machine for dirt, and clean it in time. In addition, you need to check the needle clip for debris and clean it up. In addition, the site environment should be kept clean and hygienic. When the inspection work is completed, we need to classify the fabrics to be produced according to the process conditions. Generally, the same process fabrics will be used for centr...
Post a Comment
Read more

Structural Characteristics of Hot Air Stenter Machine

The Hot Air Stenter machine is mainly composed of the feeding part, the weft feeder, the chain, the oven body, and the falling cloth. Apart from that, chemical systems and oil furnace heating systems. 1.Feeding part The structure is relatively simple, consisting of a trough and a roll. The cloth enters the trough, carries the chemical material, and then presses the excess chemical material through the roll to clean it. Therefore, the chemical material on the cloth is very uniform, which is a prerequisite for obtaining a high quality styling cloth. It is necessary to always pay attention to whether the pressure on the left and right sides of the roll is consistent. Otherwise, the side with less pressure is loaded more, while the one with higher pressure is less loaded, and the cloth will have quality problems such as inconsistency. 2. Weft feeder The weft aligner on the fixed machine has four sets of sensors. Each sensor consists of two parts: illuminating and sen...
Post a Comment
Read more

LiCheng Flat Screen Printing Machine

Zhejiang LiCheng is devoted towards offering the qualitative range of Flat Screen Printing Machine , as per client’s precise need and requirements.   Flat screen printing machine working principle: Take the commonly used hand-screen flat screen printing machine as an example, the working principle of the screen printing machine can be described as follows: The transmission mechanism transmits the power so that the squeegee squeezes the ink and the screen printing plate during the movement so that the screen Printing plate and the substrate to form a nip, the screen has tension N1 and N2, the force on the squeegee F2, rebound so that the screen printing plate in addition to the imprinting line are not in contact with the substrate, the ink in Under the action of the squeezing force F1 of the squeegee, the squeegee slides from the moving nip to the substrate through the mesh. In Flat Screen Printing Technology the screen is flat and moves up and down. the Squeez...
Post a Comment
Read more