Skip to main content

Some Information about Licheng Hot Air Stenter

With the dyeing and finishing of textiles, the warp direction is subjected to a large pulling force, resulting in elongation and narrowing of the length. In order to overcome this unstable state and ensure the dimensional stability of the textile, the speed of feeding into the cloth is adjusted during stentering or setting, which is super-feeding. The speed of feeding into the cloth is higher than the speed of the Hot Air Stenter machine called positive super-feeding (or over-feeding, shrink-code). The positive overfeeding causes the warp yarn to retract, the weft density rises, the gram weight increases and the warp direction shrinks.
 
If the speed of the cloth is less than the speed of the Hot Air Stenter setting machine, it is called anti-overfeed (or negative overfeed, pull code). The anti-overfeeding causes the warp yarn to elongate, the weft density decreases, the gram weight decreases, and the warp direction shrinks. There are many dyeing factories in China that are willing to make some violations of the principle in order to pursue their own profits.

Stretching is a finishing work after dyeing, and it is also a very important process. In the process of stentering, some dyeing factories have worked harder than the amount of grey cloth input in order to process the fabric. They are very objective in thinking that most customers do not understand the reasons for this, letting them do whatever they want.

Now I have compiled some knowledge of overfeeding during stenter setting, for reference only.

In the dyeing and finishing process, the warp direction is subjected to a large pulling force, which tends to cause a narrowing of the warp direction, which is an unstable state, and the fabric undergoes warp shrinkage in water.

LiCheng printing machine manufacturers, we offer high-quality open type rotary screen printing machine and Flat Screen Printer Machine, if you interested in learn more information, please feel free to contact us by click https://www.hotairstenter.com/
Labels:

Comments

Post a Comment

Popular posts from this blog

Feeding Operation of Hot Air Stenter

Do you are already familiar with the feeding operation of the Hot Air Stenter machine? Although this operation is relatively simple, the problems that need attention are relatively trivial, and this operation will affect the subsequent processing effect of the hot air stenter machine. So as a user, we also need to pay attention to this part of the content. In actual work, we must wear the guide cloth according to the requirements, and check the worn guide cloth to ensure correctness. Then we need to clean the hot air stenter machine first, especially pay attention to check the cloth rack and the front of the machine for dirt, and clean it in time. In addition, you need to check the needle clip for debris and clean it up. In addition, the site environment should be kept clean and hygienic. When the inspection work is completed, we need to classify the fabrics to be produced according to the process conditions. Generally, the same process fabrics will be used for centr...
Post a Comment
Read more

Structural Characteristics of Hot Air Stenter Machine

The Hot Air Stenter machine is mainly composed of the feeding part, the weft feeder, the chain, the oven body, and the falling cloth. Apart from that, chemical systems and oil furnace heating systems. 1.Feeding part The structure is relatively simple, consisting of a trough and a roll. The cloth enters the trough, carries the chemical material, and then presses the excess chemical material through the roll to clean it. Therefore, the chemical material on the cloth is very uniform, which is a prerequisite for obtaining a high quality styling cloth. It is necessary to always pay attention to whether the pressure on the left and right sides of the roll is consistent. Otherwise, the side with less pressure is loaded more, while the one with higher pressure is less loaded, and the cloth will have quality problems such as inconsistency. 2. Weft feeder The weft aligner on the fixed machine has four sets of sensors. Each sensor consists of two parts: illuminating and sen...
Post a Comment
Read more

LiCheng Flat Screen Printing Machine

Zhejiang LiCheng is devoted towards offering the qualitative range of Flat Screen Printing Machine , as per client’s precise need and requirements.   Flat screen printing machine working principle: Take the commonly used hand-screen flat screen printing machine as an example, the working principle of the screen printing machine can be described as follows: The transmission mechanism transmits the power so that the squeegee squeezes the ink and the screen printing plate during the movement so that the screen Printing plate and the substrate to form a nip, the screen has tension N1 and N2, the force on the squeegee F2, rebound so that the screen printing plate in addition to the imprinting line are not in contact with the substrate, the ink in Under the action of the squeezing force F1 of the squeegee, the squeegee slides from the moving nip to the substrate through the mesh. In Flat Screen Printing Technology the screen is flat and moves up and down. the Squeez...
Post a Comment
Read more