Skip to main content

ZCMD768 Type Hot Air Stenter

The Hot Air Stenter Machine is always used for stretching and tensioning the fabric by heating and stretching the two sides with uniform width.
The continuous flat dyeing and finishing of knitted fabrics can optimize printing quality, and reduce damage to the fabric with excellent flexibility. In addition, it can reduce the cost of the mercerizing machine.
The hot air stenter is mainly used to make the weaving machine. Generally, the hot air stenter uses the heat transfer oil to heat the air in the setting machine, and then heats the fabric. When the fabric reaches a certain temperature and remains for a certain period of time, the structure of the fabric changes to achieve the purpose of setting. The double-point lining coater is the main equipment for processing high-grade low-elastic linings and thin non-woven linings. It mainly consists of several parts such as retort, slurry coating, dust coating, up and down suction, drying room, cooling and winding, pneumatic and electrical control.
The general trend of hot air stenter technology development is: development towards environmental protection, energy saving, time saving and high efficiency, focusing on waterless processing technology, non-plate printing technology, low temperature plasma processing and other new technologies; another important The trend is to widely adopt automation technology. The transmission system adopts AC frequency conversion multi-unit synchronous speed control system. In the control system, programmable logic controller or industrial computer control is widely used. The parameters online monitoring are widely used and the dyeing is improved.
As a professionl hot air stenter manufacturer, Licheng Manufacturer always provides you with superior Printing Machine, please feel free to contact us at any time. We look forward to reaching win-win with mutual benefit with our customers together!
ZCMD768 Type Hot Air Stenter is a machine or device for stretching or tensioning a fabric that enables the length and width of the stenter to reach a predetermined size. This equipment can also be used for heat setting, for coating chemicals, and for adjusting chromatic aberrations. If you interested in learn more information, please freel free to contact us by click hotairstenter.com
Labels:

Comments

Post a Comment

Popular posts from this blog

Feeding Operation of Hot Air Stenter

Do you are already familiar with the feeding operation of the Hot Air Stenter machine? Although this operation is relatively simple, the problems that need attention are relatively trivial, and this operation will affect the subsequent processing effect of the hot air stenter machine. So as a user, we also need to pay attention to this part of the content. In actual work, we must wear the guide cloth according to the requirements, and check the worn guide cloth to ensure correctness. Then we need to clean the hot air stenter machine first, especially pay attention to check the cloth rack and the front of the machine for dirt, and clean it in time. In addition, you need to check the needle clip for debris and clean it up. In addition, the site environment should be kept clean and hygienic. When the inspection work is completed, we need to classify the fabrics to be produced according to the process conditions. Generally, the same process fabrics will be used for centr...
Post a Comment
Read more

Structural Characteristics of Hot Air Stenter Machine

The Hot Air Stenter machine is mainly composed of the feeding part, the weft feeder, the chain, the oven body, and the falling cloth. Apart from that, chemical systems and oil furnace heating systems. 1.Feeding part The structure is relatively simple, consisting of a trough and a roll. The cloth enters the trough, carries the chemical material, and then presses the excess chemical material through the roll to clean it. Therefore, the chemical material on the cloth is very uniform, which is a prerequisite for obtaining a high quality styling cloth. It is necessary to always pay attention to whether the pressure on the left and right sides of the roll is consistent. Otherwise, the side with less pressure is loaded more, while the one with higher pressure is less loaded, and the cloth will have quality problems such as inconsistency. 2. Weft feeder The weft aligner on the fixed machine has four sets of sensors. Each sensor consists of two parts: illuminating and sen...
Post a Comment
Read more

LiCheng Flat Screen Printing Machine

Zhejiang LiCheng is devoted towards offering the qualitative range of Flat Screen Printing Machine , as per client’s precise need and requirements.   Flat screen printing machine working principle: Take the commonly used hand-screen flat screen printing machine as an example, the working principle of the screen printing machine can be described as follows: The transmission mechanism transmits the power so that the squeegee squeezes the ink and the screen printing plate during the movement so that the screen Printing plate and the substrate to form a nip, the screen has tension N1 and N2, the force on the squeegee F2, rebound so that the screen printing plate in addition to the imprinting line are not in contact with the substrate, the ink in Under the action of the squeezing force F1 of the squeegee, the squeegee slides from the moving nip to the substrate through the mesh. In Flat Screen Printing Technology the screen is flat and moves up and down. the Squeez...
Post a Comment
Read more