Skip to main content

General Knowledge of Flat Screen Printer

The whole bit of guide belt of Flat Screen Printing Machine is driven by three roll whole bit principle, control roll of swing angle is dragged by electric motor ,motor of backward and forward running or stop is by two photoelectric switches which only close to the edge of guide belt , under right installation and good paring-off this institutions can guarantee guide with smooth run, partial range can control within ± 3mm.
Magnetic Chuck:
Professional magnetic provides a uniform printing penetration, magnetic chuck of Flat Screen Printer is electromagnetic type coil which designed by the latest CAD-CAM system, uniform penetration of printing paste for high-precision mechanism without left, middle right color difference, without maintenance.
Net Head Chuck:
High strength flat bearing, in line with the stress direction, increase the service life.
Stuff Pump:
Pump body of Flat Screen Printer is made of stainless steel, equipped with manual control and automatic control through slurry liquid bar and PLC control for liquid level.
Main Drive System of Printing Guide Belt
Using the CAN trunk technology and 485 communications, realizing centralized processing of the underlying data in the PC and adopt speed control as well as control of the network head, realizing print synchronization , thus ensuring the printing effect.
Show all information status through the man-machine interface to customers, user-friendly operation and management. The system passed reliability verification under high temperature, high humidity, strong corruption, strong interference environment.
Independent Drive of Net Head:
Servo motors can be controlled in a 360 ° circle Rotary precision on flowers, the cumulative error control within the 0.08mm. Main operation panel controller can be easily changed directly addresses interchangeably. High-performance converter encodes speed closed loop control. Other drive motor adopt general purpose inverter; from analogue into digital type system, thus ensuring the accuracy of synchronous control system.
Internal Electrical Control System of Frame Head:
Printing units all equipped with independent servo motors, the most advanced AC servo drivers, each unit equipped with prefabricated cable connectors through optical fiber communications to ensure the printing precision of printer, electrical system maintenance is very convenient.

Labels

Labels:

Comments

Post a Comment

Popular posts from this blog

Preliminary Preparation of Rotary Screen Printing Machine II

Requirements for the glue of Open Type Rotary Screen Printing Machine Since 80% of the defects in the printing process are caused by the printing paste, there are strict requirements on the quality of the glue, mainly including: The glue must be prepared before opening the machine . The color of the glue must match the original. The glue should maintain a proper consistency. Generally, the thinner the fabric, the greater the consistency of the glue, the finer the pattern, and the consistency of the glue. The printing paste should be fully dissolved. After the preparation is completed, the nylon mesh should be used for filtration to avoid impurities blocking the net or damage the rotary screen. Requirements for rotary screen printing machine The rotary screen printing machine should be thoroughly inspected before driving to ensure that there are no foreign objects in the printed tape to avoid damage to the tape. The temperature of the drying room should be adjust...
Post a Comment
Read more

Inaccurate Registration of Rotary Screen Printer

When two or more patterns of registrations are printed, all or part of the patterns on the printed fabric are staggered or overlapped, which is seriously inconsistent with the original, called inaccurate registration. (1)Constant Inaccurate Registration Constant Inaccurate Registration means that the registration is not inaccurate from the start of driving, and the corresponding pattern always shifts from the original position or overlaps. The low impact factors of such problems can be found in the following reasons: the accuracy of the printing machine, the rotary screen and its plate making, the process, the operation, the printed fabric, and the patch pulp. (2)Inaccurate Left and right Registration That is to say, the registration is accurate in the middle, but inaccurate on the right or left. In this case, it is necessary to check whether the mechanical operation of the rotary screen printing part is normal; whether the film draft conforms to each set of film ...
Post a Comment
Read more

ZCMD768 Type Hot Air Stenter

The Hot Air Stenter Machine is always used for stretching and tensioning the fabric by heating and stretching the two sides with uniform width. The continuous flat dyeing and finishing of knitted fabrics can optimize printing quality, and reduce damage to the fabric with excellent flexibility. In addition, it can reduce the cost of the mercerizing machine. The hot air stenter is mainly used to make the weaving machine. Generally, the hot air stenter uses the heat transfer oil to heat the air in the setting machine, and then heats the fabric. When the fabric reaches a certain temperature and remains for a certain period of time, the structure of the fabric changes to achieve the purpose of setting. The double-point lining coater is the main equipment for processing high-grade low-elastic linings and thin non-woven linings. It mainly consists of several parts such as retort, slurry coating, dust coating, up and down suction, drying room, cooling and winding, pneumatic a...
Post a Comment
Read more